RCK16-28x55 Challenge Cone Clamping Element 28x55mm
Challenge RCK16 series cone clamping element 28mm inside x 55mm outside, also known as series RF07, TLK133, CCE4600, Conex ES, FLK133, CN9/4, RFN7013.1
Regular price
£12.54
inc.VAT
£10.45 exc.VAT
FREE UK MAINLAND DELIVERY ON ORDERS OVER £50
Couldn't load pickup availability
Shaftlock Cone Clamping Elements
Cone clamping elements are a purely friction method of clamping components to a shaft. The internal components within a cone clamp operate on a taper, so as the cone clamp is tightened the internal diameter decreases while the outside diameter increases. This change in diameters creates the clamping force.
There are two main advantages of cone clamps. The first is that for machining your component (i.e. a sprocket), the bore needs to be plain rather than being keyed or tapped and tapered. The second advantage is that the cone clamp acts as an overload protector, with excessive loading causing the clamp to spin on the shaft.
Cross Reference Guide:- Tollok: TLK133, Bikon: 1006, Bonfix: CCE4600, Chiaravalli: RCK16, Compomac: Conex ES, Fenlock: FLK133, Italblock: CN9/4, Kana: 201, Kinlok: N/A, Clampex KTR: KTR206, MAV: 1061, Poggi: CAL-ES, Ringblok: 1720, Ringfeder: RFN7013.1, Ringspann: RLK133, SIT: N/A, TAS-Schafer: TAS 3006, Tsubaki Power-Lock: N/A, VBlok: VK130
To Install
1 Ensure the hub and shaft surfaces are clean and degreased.
2 Apply a thin coating of light machine oil to screw threads and conical surfaces (do not use any molybdenum disulphide based or E.P. oils).
3 Loosely assemble the clamping element into the required position and tighten the clamping screws in diagonal sequence to the requisite torque, Ts.
4 If the application is subject to corrosive environmental conditions, apply grease to protect screw heads etc.
To Remove
1 Loosen all of the clamping screws in the same diagonal sequence as assembly.
2 The clamping element should now self release.
3 If necessary, tap the screws lightly with a soft hammer.
4 If the clamping element tapers still don't release, remove some of the bolts and insert them into threaded removal holes.
5 Tighten them sequentially to break the clamping ring cone tapers.
6 Lubricate all screws with a light machine oil for the future use of the Challenge Cone Clamping Element.
Dimensions
d: 28mm
D: 55mm
D1: 64mm
L1: 17mm
L2: 22mm
L3: 28mm
L: 34mm
Transmission
Torque Mt: 431Nm
Axial Force Ft: 29kN
Contact Pressure
Shaft P: 177 N/mm2
Hub P1: 90 N/mm2
Locking Screws
Qty: 6
Size: M6x20
Tightening Torque Ts: 17Nm
Cone clamping elements are a purely friction method of clamping components to a shaft. The internal components within a cone clamp operate on a taper, so as the cone clamp is tightened the internal diameter decreases while the outside diameter increases. This change in diameters creates the clamping force.
There are two main advantages of cone clamps. The first is that for machining your component (i.e. a sprocket), the bore needs to be plain rather than being keyed or tapped and tapered. The second advantage is that the cone clamp acts as an overload protector, with excessive loading causing the clamp to spin on the shaft.
Cross Reference Guide:- Tollok: TLK133, Bikon: 1006, Bonfix: CCE4600, Chiaravalli: RCK16, Compomac: Conex ES, Fenlock: FLK133, Italblock: CN9/4, Kana: 201, Kinlok: N/A, Clampex KTR: KTR206, MAV: 1061, Poggi: CAL-ES, Ringblok: 1720, Ringfeder: RFN7013.1, Ringspann: RLK133, SIT: N/A, TAS-Schafer: TAS 3006, Tsubaki Power-Lock: N/A, VBlok: VK130
To Install
1 Ensure the hub and shaft surfaces are clean and degreased.
2 Apply a thin coating of light machine oil to screw threads and conical surfaces (do not use any molybdenum disulphide based or E.P. oils).
3 Loosely assemble the clamping element into the required position and tighten the clamping screws in diagonal sequence to the requisite torque, Ts.
4 If the application is subject to corrosive environmental conditions, apply grease to protect screw heads etc.
To Remove
1 Loosen all of the clamping screws in the same diagonal sequence as assembly.
2 The clamping element should now self release.
3 If necessary, tap the screws lightly with a soft hammer.
4 If the clamping element tapers still don't release, remove some of the bolts and insert them into threaded removal holes.
5 Tighten them sequentially to break the clamping ring cone tapers.
6 Lubricate all screws with a light machine oil for the future use of the Challenge Cone Clamping Element.
Dimensions
d: 28mm
D: 55mm
D1: 64mm
L1: 17mm
L2: 22mm
L3: 28mm
L: 34mm
Transmission
Torque Mt: 431Nm
Axial Force Ft: 29kN
Contact Pressure
Shaft P: 177 N/mm2
Hub P1: 90 N/mm2
Locking Screws
Qty: 6
Size: M6x20
Tightening Torque Ts: 17Nm