TIH 030M 110V SKF Small Induction Heater 110V Version

The SKF small induction heater TIH 030m combines high heating capacity with portability. The compact lightweight design makes the TIH 030m portable. Placing the induction coil outside the heaters housing allows the heating of bearings weighing up to 40 kg (88 lb).

The induction heater is equipped with thermal overheating protection to reduce the risk of damage to the induction coil and the electronics. In addition to temperature mode, the TIH 030m is equipped with a time mode for heating components other than bearings.

The induction heating system is supplied standard with three yokes and is available in two executions: 230V, 50/60Hz and 110V, 50/60Hz.

Compact lightweight design; just 20.9 kg (46.0 lb) facilitating portability
2-step power setting and smaller yokes allow heating smaller bearings safely and at lower power consumption
Foldable bearing support arms allow larger diameter bearings to be heated, and reduce the risk of the bearing toppling during heating
Capable of heating a 28 kg (61.7 lb) bearing in just 20 minutes
Temperature mode pre-set at 110 °C (230 °F) to help prevent bearing over-heating
Automatic demagnetization

TECHNICAL DATA
Designation TIH 030M/230V TIH 030M/110V

Description Induction heater

SKF m20 performance 28 kg (61.7 lb)
Voltage, V/Hz 230V, 50/60Hz or 110V, 50/60Hz
Bearing:
- Maximum weight 40 kg (88 lb)
- Maximum bore diameter 20 - 300 mm (0.8 - 11.8 in.)
Temperature control:
- Range * 0 - 250 °C (32 - 482 °F)
- Magnetic probe Yes, K-type
- Accuracy (electronics) 2 °C ( 3.6 °F)
Time control:- Range 0 - 60 minutes
- Accuracy ± 0.01 sec.
Performance example :- bearing, weight, temperature, time 23136 CC/W33, 28 kg, 110 °C, 20m
Thermometer mode Yes
Bearing mode Yes
Power setting 2-step; 50% or 100%
Demagnetisation according to SKF norms (automatic) Yes (<2 A/cm)
Can heat sealed bearings Yes
Can heat pre-greased bearings Yes
Error guiding codes Yes
Thermal overload protection Yes
Control panel Control panel and LED display integrated in remote control
Operating area (w x h) 100 x 135 mm (3.9 x 5.3 in.)
Coil diameter 95 mm (3.7 in.)
Dimensions (w x d x h) 450 x 195 x 210 mm (17.7 x 7.6 x 8.2 in.)
Total weight, including yokes 20.9 kg (46.0 lb)
Maximum power consumption 2.0 kVA
Standard yokes
45 x 45 x 215 mm (1.7 x 1.7 x 8.4 in.) for heating bearings with bore diameter of 65 mm (2.6 in.) and larger.
28 x 28 x 215 mm (1.1 x 1.1 x 8.4 in.) for heating bearings with bore diameter of 40 mm (1.6 in.) and larger.
14 x 14 x 215 mm (0.5 x 0.5 x 8.4 in.) for heating bearings with bore diameter of 20 mm (0.8 in.) and larger
Core cross section 45 x 45 mm (1.7 x 1.7 in.)
Bearing support arms Yes, foldable
Yoke storage Yes, internal integrated in foldable bearing support arms
Cooling fan No
Swivel arm No
Housing material Steel and glass filled polyamide
* Maximum heating temperature capacity depends on the weight and geometry of the bearing or workpiece. The heaters can achieve higher temperatures, please contact SKF for advice.